The fixed speed (FS) as standard Hydrovane HV15 is enclosed for quiet operation, and with a small footprint and low noise levels these compressors can be conveniently located at the point of use. With Hydrovane, installation is hassle-free. All enclosed units fit through a standard 36” (914mm) door providing the most versatile compressor range in the market. The Hydrovane HV15 is now available with the Regulated Speed (RS) option, which precisely matches the compressor speed to the compressor output. The direct drive low RPM ensures a reliable pulse free supply of good quality, quietly produced compressed air. If used correctly the Regulated Speed (RS) machines can deliver benefits of up to 50% in energy savings compared to the equivalent standard fixed speed model. The Hydrovane HV15 also comes with the options to add a fully integrated 272L receiver or a refrigerant dryer (Hypac package), or both (Air Solution package) to your compressor to offer you the best solution for your compressed air requirements.

• 15kW motor power
• Available as either standard Fixed Speed (FS) or with Regulated Speed (RS) option
• Available with integrated 272L receiver and/or refrigerant dryer options (50Hz only):
  • Pressure dew point with receiver only: 8C
  • Pressure dew point with refrigerant dryer only: 3C
  • Pressure dew point with receiver and refrigerant dryer: 3C
• Available as 50Hz or 60Hz type:
  • 50Hz – 400V, 3 phase
  • 60Hz – 460V, 3 phase (standalone only)
• Available as 6 bar (RS only), 8 bar or 10 bar type:
  • 6 bar (RS) – 80.8cfm max (same @ 50Hz/60Hz)
  • 8 bar (FS) – 78.1cfm max @ 50Hz or 67.1cfm max @ 60Hz
  • 8 bar (RS) – 71.6cfm max (same @ 50Hz/60Hz)
  • 10 bar (FS) – 71.0cfm max @ 50Hz or 58.4cfm max @ 60Hz
  • 10 bar (RS) – 60.7cfm max (same @ 50Hz/60Hz)
• Low noise, at only 70dB(A)
• Sized as follows, dependant on specification:
  • Standalone unit: 1550mm (h) x 700 (w) x 850 (d)
  • With integrated receiver: 1550mm (h) x 1355 (w) x 1187 (d)
  • With integrated refrigerant dryer: 1550mm (h) x 1215 (w) x 825 (d)
  • With integrated receiver and refrigerant dryer: 1550mm (h) x 1355 (w) x 1187 (d)
• Air quality: < 3 mg/m3 (standalone), < 2 mg/m3 (with receiver only), < 1 mg/m3 (with refrigerant dryer or receiver and refrigerant dryer)
• Clean, dry and pulse free straight from the outlet means less downstream equipment required
• No gears, no belts. Up to 100,000+ operating hours due to its simple integral design
• 12 month warranty extendable to 10 years (5 years on the Regulated Speed inverter). Conditional to the unit being sited, operated and maintained correctly by a Hydrovane approved distributor (Airware International is an approved distributor! Get in touch with us today to find out more)
• Fitted with REVS (Reduced Energy Venting System) as standard

Download and view the official Hydrovane brochure under the “Documentation” tab above!

The AMD series of refrigerant dryers are matched to standard air compressor outputs to allow economic unit selection. AMD dryers use the ALU DRY aluminium modular heat exchanger which has a vertical flow layout ensuring wet compressed air flows down to the condensate drain.

• AMD 25 Flow rate 2500 l/min 88 cfm @ 5C pressure dew point
• 15kW/20HP
• Connections: 1″ BSP-F
• 345mm (w) x 420mm (d) x 740mm (h)
• Max inlet pressure 14 bar
• 230v single phase electrical supply required
• Packed weight 38kg

• 15kW 3 phase electric motor, 20hp
• 79.5 cfm, 2.25 m3/min 8 bar
• 78.4 cfm, 2.22 m3/min 10 bar
• 8 bar/115 psig maximum pressure
• 10 bar/150 psig maximum pressure
• Extremely quiet at only 59.5 dB (A)
• LCD Pressure Transducer BASIC control panel with 24v control voltage as standard
• Aftercooler as standard – Discharge air is kept at only 10C or 15C above ambient, with frost protection control
• 1335 (W) x 693 (D) x 610 (H) base unit, 1815 (W) x 720 (D) x 1365 (H) inc receiver, 1960(W) x 720 (D) x 1365 (H) inc receiver and dryer (without sound insulating hood)
• 1500 (W) x 784 (D) x 800 (H) base unit, 1820 (W) x 835 (D) x 1495 (H) inc receiver, 2040 (W) x 835 (D) x 1500 (H) inc receiver and dryer (with sound insulating hood)
• 300kg base unit 8 bar/10 bar, 380kg inc receiver 8 bar/10 bar, 470kg inc receiver and dryer 8 bar/10 bar (unpacked weight without sound insulating hood)
• 435kg base unit 8 bar/10 bar, 575kg inc receiver 8 bar/10 bar, 610kg inc receiver and dryer 8 bar/10 bar (unpacked weight with sound insulating hood)
• Delivery generally ex-stock

Available with no receiver – base unit only – C20L, an RM 350 Litre receiver mounted – C20LR or with an RM 350 Litre receiver with dryer – C20LDR (cost will change accordingly). Please pick from the above dropdown to enable purchase.

Available with the following pressure options: “8 bar” and “10 bar”. Please pick from the above dropdown to enable purchase. 

Also available with sound insulating hood for an additional cost. Please pick ‘Included’ from the above dropdown if required.