The fixed speed Hydrovane HR07PR is a small and compact open air compressor, ideally suited for light industrial and workshop applications where the compressed air outlet needs to be situated close to the point of use. Featuring a 200L receiver mounted as standard, the HR07PR is ready to go from the moment it reaches you. Specification includes:

• 7.5kW motor power
• 200L receiver mounted
• 50Hz – 400V, 3 phase
• Pressure set to 10 bar providing 35.0cfm max
• SD (Star Delta) Starter fitted
• Low noise, at only 73dB(A)
• 1068mm (h) x 1332mm (w) x 570mm ( d)
• Air quality: < 3 mg/m3
• Clean, dry and pulse free straight from the outlet means less downstream equipment required
• No gears, no belts. Up to 100,000+ operating hours due to its simple integral design
• 12 month UK wide warranty provided

Download and view the official Hydrovane brochure under the “Documentation” tab above!

The fixed speed (FS) as standard Hydrovane HV07E is enclosed for quiet operation, and with a small footprint and low noise levels these compressors can be conveniently located at the point of use. With Hydrovane, installation is hassle-free. All enclosed units fit through a standard 36” (914mm) door providing the most versatile compressor range in the market. The Hydrovane HV07E is now available with the Regulated Speed (RS) option, which precisely matches the compressor speed to the compressor output. The direct drive low RPM ensures a reliable pulse free supply of good quality, quietly produced compressed air. If used correctly the Regulated Speed (RS) machines can deliver benefits of up to 50% in energy savings compared to the equivalent standard fixed speed model. The Hydrovane HV07E also comes with the options to add a fully integrated 260L receiver or a refrigerant dryer (Hypac package), or both (Air Solution package) to your compressor to offer you the best solution for your compressed air requirements.

• 7.5kW motor power
• Available as either standard Fixed Speed (FS) or with Regulated Speed (RS) option
• Available with integrated 260L receiver and/or refrigerant dryer options:
  • Pressure dew point with receiver only: 8C
  • Pressure dew point with refrigerant dryer only: 3C
  • Pressure dew point with receiver and refrigerant dryer: 3C
• 50Hz – 400V, 3 phase
• Available as 7 bar (FS only) or 10 bar type:
  • 7 bar (FS): 44.1cfm max
  • 10 bar (FS): 35.0cfm max
  • 10 bar (RS): 34.3cfm max
• Low noise, at only 67dB(A) (FS), or 70dB(A) (RS)
• Sized as follows, dependant on specification:
  • Standalone unit: 1055mm (h) x 630 (w) x 680 (d)
  • With integrated receiver: 1165mm (h) x 1146 (w) x 685 (d)
  • With integrated refrigerant dryer: 1078mm (h) x 630 (w) x 968 (d)
  • With integrated receiver and refrigerant dryer: 1165mm (h) x 1146 (w) x 968 (d)
• Air quality: < 3 mg/m3 (standalone), < 3 mg/m3 (with receiver only), < 1 mg/m3 (with refrigerant dryer or receiver and refrigerant dryer)
• Clean, dry and pulse free straight from the outlet means less downstream equipment required
• No gears, no belts. Up to 100,000+ operating hours due to its simple integral design
• 12 month warranty extendable to 10 years (5 years on the Regulated Speed inverter). Conditional to the unit being sited, operated and maintained correctly by a Hydrovane approved distributor (Airware International is an approved distributor! Get in touch with us today to find out more)
• Fitted with REVS (Reduced Energy Venting System) as standard

Download and view the official Hydrovane brochure under the “Documentation” tab above!

The new S-Series of oil-free scroll compressors from Champion does not use any oil anywhere in the compressor and has been certified ISO 8573-1 Class 0 and silicone free, which represents the highest air quality level possible. The S-Series S8 compressor is also very versatile and has multiple configuration set-ups, please select from the drop-downs above to configure your S-Series compressor to your requirements (and please get in touch if you need any assistance!).

• Available as 8 or 10 bar type
• 53.0m3/h capacity @ 8 bar or 41.3m3/h capacity @ 10 bar
• 7.5kW electric motor
• 100% oil free
• Inbuilt automatic condensate drain
• High volume cooling fan
• Low noise sound enclosure, including internal vibration isolators
• Available in either 230v, 50/60Hz or 400v, 50/60Hz
• Available with Standard or Soft Start operation (400v, 50/60Hz only – Soft Start reduces energy consumption as the compressor runs only when needed)
• Available with two controller types:
  • Basic Relay Control Panel:
    • NEMA 1 UL508A Labeled Panel with operation on light
    • Magnetic Contactor with Overload Protection
    • 115V Control Circuit Transformer with Fusing
    • Emergency Stop and Reset Buttons
    • Run Time Meter and Pressure Gauge
  • Deluxe HMI Control Panel:
    • 3.5″ Full Colour Touch Screen with 26 Language Options
    • Integral Webserver via Modbus TCP Interface over Ethernet (allows visibility of the system from any computer/mobile with an internet connection)
    • PLC Controlled
    • Lead/Lag Control with Forced Alternation
    • System Capacity and Operation Trending
    • 24V / DC Power Supply with Fusing
    • System Run Time Meter
    • Alarm/Fault Log
    • System Discharge Pressure
    • Pump Discharge Temperature
    • System Maintenance Timers

The AMD series of refrigerant dryers are matched to standard air compressor outputs to allow economic unit selection. AMD dryers use the ALU DRY aluminium modular heat exchanger which has a vertical flow layout ensuring wet compressed air flows down to the condensate drain.

• AMD 12 Flow rate 1200 l/min 42 cfm @ 5C pressure dew point
• 7.5kW/10HP
• Connections: 1/2″ BSP-F
• 370mm (w) x 515mm (d) x 475mm (h)
• Max inlet pressure 16 bar
• 230v single phase electrical supply required
• Packed weight 30kg

• 7.5kW 3 phase electric motor, 10hp
• 37.1 cfm, 1.05 m3/min 8 bar
• 36.4 cfm 1.03 m3/min 10 bar
• 8 bar/115 psig maximum pressure
• 10 bar/150 psig maximum pressure
• Extremely quiet at only 59.5 dB (A)
• LCD Pressure Transducer BASIC control panel with 24v control voltage as standard
• Aftercooler as standard – Discharge air is kept at only 10C or 15C above ambient, with frost protection control
• 1170 (W) x 600 (D) x 600 (H) base unit, 1815 (W) x 720 (D) x 1350 (H) inc receiver, 1960(W) x 720 (D) x 1350 (H) inc receiver and dryer (without sound insulating hood)
• 1500 (W) x 784 (D) x 800 (H) base unit, 1820 (W) x 835 (D) x 1495 (H) inc receiver, 2040 (W) x 835 (D) x 1500 (H) inc receiver and dryer (with sound insulating hood)
• 260kg base unit 8 bar/10 bar, 350kg inc receiver 8 bar/10 bar, 380kg inc receiver and dryer 8 bar/10 bar (unpacked weight without sound insulating hood)
• 395kg base unit 8 bar/10 bar, 515kg inc receiver 8 bar/10 bar, 550kg inc receiver and dryer 8 bar/10 bar (unpacked weight with sound insulating hood)
• Delivery generally ex-stock

Available with no receiver – base unit only – C10L, an RM 350 Litre receiver mounted – C10LR or with an RM 350 Litre receiver with dryer – C10LDR (cost will change accordingly). Please pick from the above dropdown to enable purchase.

Available with the following pressure options: “8 bar” and “10 bar”. Please pick from the above dropdown to enable purchase. 

Also available with sound insulating hood for an additional cost. Please pick ‘Included’ from the above dropdown if required.

Compared to other compressors, the BLADE’s very low rotational speed, a distinctive feature of a Mattei compressor, means more air, greater reliability, reduced energy consumption and quiet operation. This range leverages Mattei’s proprietary rotary vane technology with a dual belt transmission, housed with a sleek, powder coated cabinet. Specification includes:

• 7.5kW 10hp 3 phase motor
• 8 bar 115 psig model – 1.085 m3/min 38 cfm
• 10 bar 150 psig model – 1.025 m3/min 36 cfm
• 13 bar 175 psig model – 0.9 m3/min 32 cfm
• 64 dB(A)
• 950mm (L) x 730mm (W) x 800mm (H) (base unit)
• 1530mm (L) x 730mm (W) x 1340mm (H) (base unit plus receiver)
• 400V/50HZ/3
• 5 year unlimited hours air end warranty
• 2 year warranty on other key components
• 195kg base unit, 265kg inc receiver, 295kg inc receiver and dryer (unpacked weight)

Available with no receiver (base unit only), a 270 Litre receiver mounted – BLADE S or with a 270 Litre receiver with dryer – BLADE SE (cost will change accordingly). Please pick from the above dropdown to enable purchase.

Also available in the following models: “8 bar/115 psi”, “10 bar/145 psi” and “13 bar/189 psi” (cost will change accordingly). Please pick from the above secondary dropdown to enable purchase.